Zandronum

So one day as I was playing It was going fine and all. But after a few levels on a server this happened.






I really need help. As im playing it annoys the living hell out of me (No pun intended).

EDIT: Also i have re-installed Zandronum 4 times. Still nothing.

Hmm are you playing on a virtual machine or something like wine?

EDIT: Does it start this way or when you play a sometime it happens? I had a problem that I saw weird things on my screen before some time (1-3 minutes) playing, 1 month latter my gpu dead =/

No im not playing on any virtual machine. It just happen. Like out of no where. Im on a windows 7 Intel Pentium.

EDIT: It happens all the time on OPENGL but not on Software or GZDoom.

Try turning on V-Sync in the OpenGL options. VSync is supposed to help with screen tearing IIRC.

It didn't work. Thank you anyway.

Do you have an integrated graphics card? Some intel cards have little/no support for openGL

What is your graphic card? Do you have any problems in others games apart zandronum?

I have a Intel(R) HD Graphics (Pentium) and no I have never had any problems besides frames skipping because of HQx4. Also i have turned that off and it didn't work. Yes the intel has little support for OPENGL but for two years i've never seen this before.

EDIT: Skulltag works fine. Zandronum is basicly Skulltag upgraded so yeah.

---

Here.
GZDoom.

Skulltag.

Zandronum.


Now im even more confused. I think i'll sleep on it and check the thread tomorrow.

import yar config and see if still appears.

I heard that stuff like this could be caused by your graphics hardware overheating, do you have proper cooling on your machine (I assume you're using a laptop)?

I have normal setup. On a table. Mouse and mousepad pluged into in the side.... Im pretty sure it gets enough cooling and I did clean my laptop not long ago (IT. WAS. DIRTY.).

Tux wrote: import yar config and see if still appears.

What?? What do you mean?

Flynn_Taggart95 wrote: Try turning on V-Sync in the OpenGL options. VSync is supposed to help with screen tearing IIRC.

Lol, that's not even screen tearing. Not even close.

This is stuff I've seen happen on overheating laptops with integrated GPUs, along with ones that are simply old or have outdated drivers.

First, I suggest updating your graphics drivers. If that fails, try running Z& in GL Compatibility Mode.

If even that fails and it turns out to be a heat problem, clean out your laptop again, more thoroughly with a can of computer duster (compressed air, be careful to not spin your lappy's fans too fast or you may wreck them. Stick something like a toothpick into the fan blades to keep them from spinning while you puff the dust through the vents in the OPPOSITE direction of normal airflow). If this doesn't help, you might have to throttle your CPU by 5-15% to keep it from generating too much heat.

GL Compatibility mode helped alot. Its less annoying now and not showing up everywhere. Thank you. I seriously thank you so much.

EDIT: Also. First thread. This place is very helpful and nice. I'll stick around for awhile.

I have found GL compatibility mode to have a lot of problems though, for instance it sometimes does not correctly render line horizons.

Hypnotoad wrote: I have found GL compatibility mode to have a lot of problems though, for instance it sometimes does not correctly render line horizons.

Also disables mirrors IIRC. But then that was a better option than having the drivers crash on my old laptop with crappy integrated graphics.

Gl comp is a nice way, but there something else, you only have the problem in zan and not in st or gzdoom... Anyway

Try deleting or renaming your Zandronum ini file.

I found out what it was. Over in the OpenGL settings in shaders theres this thing called 'Shaders for fog" I turned it off to see the lines went bye-bye. You should of heard my dramtic me screaming "YESS!!!!!". xD Anyway thanks all of you for the help.